If you’re asking “why is my furnace not heating” in the middle of an Omaha winter, the cause usually comes down to one of a handful of common problems, and several of them you can check yourself in a few minutes. Here’s a quick answer first, followed by what each cause looks like, what’s safe to try on your own, and when it’s time to call a technician.

Quick Answer: Most Common Reasons a Furnace Isn’t Heating

  • The thermostat is set wrong, has dead batteries, or is malfunctioning
  • A dirty or clogged air filter is restricting airflow
  • The furnace has overheated and shut itself off as a safety measure
  • The pilot light or electronic ignition has failed
  • The gas supply is off or interrupted
  • A tripped breaker or a switched-off furnace power switch
  • A clogged condensate line on a high-efficiency furnace
  • Leaky or blocked ductwork keeping warm air from reaching your rooms

Safety First: When Not to Troubleshoot

Before you start checking anything, two situations mean you should stop and get help right away. If you smell gas, leave the house, then call MUD (Metropolitan Utilities District) or 911 from outside. Don’t flip switches or try to relight anything. And if your carbon monoxide detector goes off, get everyone out of the home and call 911. A furnace that isn’t heating is an inconvenience; a gas leak or CO problem is an emergency.

Thermostat Problems

It sounds too simple, but the thermostat is one of the most common reasons we get called out for a furnace that “won’t heat.” Make sure it’s set to “heat,” not “cool” or “off,” and that the set temperature is actually above the current room temperature. If your thermostat runs on batteries, a weak battery can cause it to lose its settings or stop signaling the furnace altogether. Programmable and smart thermostats can also get stuck on an old schedule after a power outage.

Dirty or Clogged Air Filter

A clogged filter is the furnace equivalent of trying to breathe through a pillow. When airflow gets restricted, the heat exchanger can overheat, and the furnace’s safety controls will shut the burners down to protect the system. The result is a furnace that runs for a few minutes, shuts off, and leaves your home cold. During Omaha’s heating season, check your filter monthly and replace it every one to three months, more often if you have pets.

Furnace Overheating and Short Cycling

If your furnace turns on, runs briefly, then shuts off over and over, it’s likely short cycling. Overheating from restricted airflow is the most common cause, but a faulty flame sensor or an oversized furnace can cause the same pattern. Short cycling wears out components quickly and drives up your energy bill, so it’s worth addressing rather than living with.

Pilot Light or Ignition Failure

Older furnaces use a standing pilot light, while most newer models use electronic ignition. If the pilot is out or the igniter has failed, the burners never light and the blower just pushes room-temperature air through the vents. That’s often why a furnace seems to be running but blowing cold air. A dirty flame sensor is another frequent culprit: the burners light for a few seconds, the sensor fails to confirm the flame, and the system shuts the gas off as a precaution.

Gas Supply Issues

If the gas valve to the furnace has been turned off, or there’s a problem with your home’s gas service, the furnace has nothing to burn. Check that the gas valve near the furnace is in the “on” position, which usually means the handle runs parallel to the pipe. If other gas appliances like your stove or water heater aren’t working either, the issue may be with the gas service itself rather than the furnace.

Electrical Problems

Your furnace needs electricity to run the blower, the ignition, and the controls, even if it burns gas. Check your electrical panel for a tripped breaker, and look for the furnace power switch, which often looks like an ordinary light switch on or near the unit. These switches get flipped off by accident more often than you’d think.

Clogged Condensate Line (High-Efficiency Furnaces)

High-efficiency furnaces produce condensation that drains through a small line or pump. If that line clogs or freezes, which can happen during a hard Nebraska cold snap, a safety switch shuts the furnace down to prevent water damage. If you see water pooling near your furnace or hear gurgling, this may be the cause.

Leaky or Blocked Ductwork

Sometimes the furnace is producing heat just fine, but the warm air never makes it to where you need it. Closed or blocked vents, disconnected duct sections, and leaks in unconditioned spaces like attics or crawlspaces can leave certain rooms cold while the rest of the house is comfortable.

What You Can Safely Check Yourself vs. When to Call a Pro

Safe to check yourself:

  • Thermostat mode, temperature setting, and batteries
  • Air filter condition
  • The furnace power switch and circuit breaker
  • The gas valve position
  • Open, unblocked supply and return vents

Best left to a technician:

  • Ignition, pilot light, or flame sensor problems
  • Gas supply or gas valve issues beyond the shutoff position
  • Electrical or control board faults
  • Short cycling that continues after a filter change
  • Any problem that comes back after you’ve reset it

If you’ve worked through the basics and your home still isn’t warming up, it’s time for professional furnace repair in Omaha. Our technicians diagnose the actual cause before recommending anything, and we’re available 24/7 because furnaces have a way of quitting on the coldest night of the year.

How to Prevent Furnace Problems This Winter

Most of the breakdowns we see in January trace back to something that could have been caught in October. A yearly tune-up cleans the burners and flame sensor, tests the ignition and safety controls, and checks for airflow and venting issues before they leave you without heat. According to the U.S. Department of Energy’s guide to furnaces and boilers, regular maintenance is one of the best ways to keep a furnace running efficiently and avoid premature failure. If your system hasn’t been looked at this season, our furnace maintenance visits are a quick way to get ahead of it.

If you heat your home with a geothermal system instead of a gas furnace, the troubleshooting looks different. Our guide to geothermal heating repair covers the most common issues with ground-source systems.

Repair or Replace?

If your furnace is under 15 years old and the problem is a single part like an igniter, flame sensor, or thermostat, a repair almost always makes sense. If your furnace is 15 to 20 years old, needs repairs every winter, or your heating bills keep climbing, replacement may save you more over time. We’ll give you an honest recommendation either way, and for bigger projects we offer financing options to help spread out the cost of a new system.

Frequently Asked Questions

Why is my furnace running but not heating my house? The most common causes are a clogged air filter, a failed igniter or dirty flame sensor, or a thermostat set to run the fan constantly. In each case the blower runs, but the burners either aren’t lighting or are shutting off early.

Why is my furnace blowing cold air? Cold air from the vents usually means the burners aren’t lighting, often because of an ignition problem, a dirty flame sensor, or an interrupted gas supply. It can also happen briefly at startup before the heat exchanger warms up.

Can a dirty filter really stop my furnace from heating? Yes. A clogged filter restricts airflow, which can cause the furnace to overheat and shut off as a safety precaution. Replacing the filter is one of the first things to check.

Is it safe to reset my furnace myself? Checking the thermostat, filter, breaker, and power switch is safe. If the furnace keeps shutting off after a reset, or if you smell gas or your CO detector goes off, stop and call for help.

How often should a furnace be serviced in Omaha? Once a year, ideally in early fall before heating season starts. Annual maintenance catches worn parts and safety issues before they lead to a breakdown in the middle of winter.

Get Your Heat Back On

A furnace that won’t heat is stressful, especially when Omaha temperatures drop below zero. Most problems are straightforward to fix once they’re properly diagnosed. If it’s summer and your AC is the one acting up, our guide on why your AC is not cooling walks through the cooling side. Otherwise, contact our team any time your furnace isn’t keeping up, day or night.

©2026 Complete Comfort Heating and Cooling

CONTACT US

Need a Quote? Contact us and a representative will be in contact within 4 business hours.

Sending

Log in with your credentials

Forgot your details?